Dynasonics TFX Ultra Transit Time Flow Meters Manuel d'utilisateur télécharger pdf (Page 50)

CH PSWD? — Change Password (Value)

0…9999

The password comes from the factory set to 0000. When set to 0000 the password function is disabled. By changing the

password from 0000 to some other value (any value between 0001…9999), configuration parameters will not be accessible

without first entering the password value when prompted. If the value is left at 0000, no security is invoked and unauthorized

changes can be made. Access to resetting of the totalizer is also protected by this password. If the password is lost or

forgotten, contact the manufacturer for a universal password to unlock the meter.

SER MENU  SERVICE MENU

The SER MENU menu allows access to meter set up values that may need revision due to application specific conditions and

information valuable in troubleshooting.

SSPD mps — Liquid Sound Speed (Meters per Second) (Reported by Firmware)

SSPD fps — Liquid Sound Speed (Feet per Second) (Reported by Firmware)

The flow meter performs an actual speed of sound calculation for the liquid it is measuring. This speed of sound calculation

will vary with temperature, pressure and fluid composition.

The meter will compensate for fluid sound speeds that vary within a window of ± 10% of the liquid specified in the BSC MENU.

If this range is exceeded, error code 0011 will appear on the display and the sound speed entry must be corrected.

The value indicated in SSPD measurement should be within 10% of the value entered/indicated in the BSC MENU item

FLUID SS. (The SSPD value itself cannot be edited.) If the actual measured value is significantly different (> ± 10%) than the

BSC MENU’s FLUID SS value, it typically indicates a problem with the instrument setup. An entry such as FL TYPE, PIPE OD or PIPE

WT may be in error, the pipe may not be round or the transducer spacing is not correct.

Table 10 lists sound speed values for water at varying temperatures. If the meter is measuring sound speed within 2% of the

table values, then the installation and setup of the instrument is correct.

Temperature Velocity Temperature Velocity Temperature Velocity

° C ° F mps fps ° C ° F mps fps ° C ° F mps fps

0 32 1402 4600 80 176 1554 5098 160 320 1440 4724

10 50 1447 4747 90 194 1550 5085 170 338 1412 4633

20 68 1482 4862 100 212 1543 5062 180 356 1390 4560

30 86 1509 4951 110 230 1532 5026 190 374 1360 4462

40 104 1529 5016 120 248 1519 4984 200 392 1333 4373

50 122 1543 5062 130 266 1503 4931 220 428 1268 4160

60 140 1551 5089 140 284 1485 4872 240 464 1192 3911

70 158 1555 5102 150 302 1466 4810 260 500 1110 3642

Table 10: Sound Speeds for water

SIG STR — Signal Strength (Reported by Firmware)

The SIG STR value is a relative indication of the amount of ultrasound making it from the transmitting transducer to

the receiving transducer. The signal strength is a blending of esoteric transit time measurements distilled into a usable

overall reference.

The measurement of signal strength assists service personnel in troubleshooting the flow meter system. In general, expect

the signal strength readings to be greater than five on a full pipe with the transducers properly mounted. Signal strength

readings that are less than five indicate a need to choose an alternative mounting method for the transducers or that an

improper pipe size has been entered.

Signal strength below the low signal cutoff SIG C-OF value will generate a 0010 error (Low Signal Strength) and require either

a change in the SIG C-OF value or transducer mounting changes.

SER MENU  SERVICE MENU

Page 50 March 2014

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 107 108

Commentaires sur ces manuels

Pas de commentaire

Dynasonics TFX Ultra Transit Time Flow Meters Manuel d'utilisateur Page 50

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Dynasonics TFX Ultra Transit Time Flow Meters